Forged Steel Grinding Ball: How to Review Batch Acceptance Evidence

2026-11-20

To accept a forged steel grinding ball batch, match the delivery to the purchase specification, verify that the inspection report covers the lot received, and check each required result against the agreed method and limit. If a report covers only one of two lots in a shipment, review that lot separately. Keep the other lot pending until its evidence is available.


At Iraeta, we supply forged grinding balls in diameters from 20 to 160 mm across six material grades. For an order covering several diameters or grades, agree with us before production on how the items will be identified and which records are required for release. The confirmed purchase specification governs acceptance of the delivered material.

forged steel grinding ball

Match Grinding Ball Lots to Their Inspection Reports


Consider an illustrative delivery of 80 mm grinding balls in one agreed grade. The packing list identifies two lots, A and B, but the dimensional report identifies only Lot A. The reported measurements meet the agreed diameter limits. Lot A passes the dimensional review if the method and sampling also meet the purchase specification. Lot B remains pending dimensional verification. Neither lot is ready for release until its other required checks are complete.


Follow each order line through the packing list, the agreed product or packaging identification, and the inspection report. Match the nominal diameter, grade, and lot identifier. A report for the correct diameter and grade may still cover a different lot. If identifiers differ across documents, send us the discrepancy and request the record linking the report to the delivery.


Traceability checkWhat to matchReview outcome
Purchase order lineNominal diameter, material grade, and quantityIdentify the order line fulfilled by the delivery.
Shipment and packaging identificationLot identifiers and quantities included in the shipmentList the lots received and note quantity or identification discrepancies.
Inspection reportReported lot or sample identifier and its link to the delivered materialList the lots covered by each report. Keep any unlinked lot pending.
Split shipmentQuantity dispatched against each order line and lotSeparate the quantity received from the balance still to ship.


When one report covers several lots, verify that each covered lot is identified and that the order permits the agreed sampling or grouping. Do not extend the report to an additional lot solely because it has the same diameter and grade. For deliveries containing several sizes, complete the document check against each affected order line.


If the material can be reliably separated and your receiving procedure permits partial release, an open item for one lot need not hold up a fully verified lot. If separation or identification is uncertain, resolve it before releasing any affected material.


Check Grinding Ball Test Results Against the Order


Compare each reported result with the applicable order requirement. Check the unit, test method, measurement or specimen conditions, and sampling basis before assessing the value. If the order requires measured results, a statement of compliance alone leaves the reporting requirement open.


Diameter and Hardness


For diameter, compare the measurements with the tolerance specified for the ordered size. The nominal diameter identifies the product; the measured values establish its dimensional condition. If the order requires individual readings, verify that they are present rather than accepting an average in their place.


For hardness, check the scale and measurement location. A surface reading does not establish core hardness or the hardness profile through the ball. If your specification requires readings at several locations, list those locations in the purchase agreement and confirm that the report includes them. Where a location or scale is missing, request clarification before closing the check.


Impact Toughness and Breakage Rate


For impact toughness, review the test method, specimen details and conditions, reported unit, and acceptance limit. If the purchase specification requires a particular specimen detail, verify it in the report. A hardness result cannot replace a missing impact toughness result.


For breakage rate, agree what counts as breakage, the population used to calculate the percentage, and the assessment conditions. Iraeta lists a breakage rate of no more than 0.5% in our grinding ball specifications and RFQ guide. That published figure is not a measured result for the delivered lot or a guarantee for a particular mill. If breakage rate is an acceptance requirement, specify the method, limit, and evidence required in the order.


Keep test results tied to their stated purpose. A result obtained under an agreed inspection method supports review against that requirement. It does not establish performance under different operating or assessment conditions. Refer unresolved method differences to the technical review before comparing the reported percentage with the order limit.


Keep Batch Results, Process Records, and Certificates Separate


We use computer-controlled grinding media production and a composite heat-treatment process combining multi-stage quenching, controlled quenching-liquid temperatures, and continuous tempering. Our grinding media production and quality controls support manufacturing consistency. For release of an individual lot, review the finished-product results and any additional records required by the order.


If your qualification procedure requires a heat-treatment record, check its connection to the lot under review. If the order requires a finished-ball hardness result, check that result separately. A quenching record does not close the hardness requirement, even when both documents identify the same lot. List required process records before production rather than assuming they are included with every shipment.


Review certificates against their actual scope. For a management-system certificate, check the named organization, stated activities, applicable locations, and validity. Do not extend its coverage to every factory or product sold under the brand. If the purchase requires a product certificate, verify that the certificate and any scope annex cover the grinding balls being ordered.


Keep supplier qualification documents separate from lot acceptance records in the receiving review. A certificate required for supplier approval does not replace a lot-specific report required by the purchase order. Conversely, a conforming lot report does not close a missing qualification document when your approval procedure requires it.


Grinding Ball Batch Release: Accept, Hold, or Review

Record the affected lot, the requirement under review, and the evidence still needed. Distinguish missing evidence from a reported result outside the agreed limit. The first leaves compliance unverified; the second requires disposition of a nonconforming result.


Receiving review findingStatusNext action
Lot identity is confirmed and all required checks meet the specificationEligible for releaseRecord the report references and obtain the approval required by your procedure.
Report cannot be linked to the delivered lotPending traceabilityRequest a corrected report or a record connecting the report to the lot.
Required result, specimen detail, or test condition is missingPending verificationRequest the missing evidence and agree on additional verification if the original record cannot resolve the issue.
A reported result falls outside the agreed limitNonconforming resultKeep the affected material separate and refer it for formal disposition.
One lot meets the requirements and another remains openPartial release, if permittedRelease only the identified conforming lot and retain the other on hold.


For Lots A and B in the opening example, a revised report can close Lot B’s document gap only if it establishes coverage under the agreed method and sampling basis. If the original test record does not cover Lot B, keep the lot pending while the required verification is arranged.


If a measured result is outside the order limit, record the nonconformity against the affected lot and quantity. Any additional test should follow an agreed review plan; do not select a new sample simply to replace an unfavorable result. If your procedure permits a concession, document the specific requirement, affected quantity, and authorized decision separately. A concession authorizes a defined disposition; it does not change the original result.


Before an accepted lot enters available stock, retain the report references and release decision against its identifier. Where the delivery is split between released and held material, keep the quantities clear in both the receiving record and the storage arrangement. This prevents an unresolved lot from being issued with material already approved.


Put the Next Delivery’s Evidence Requirements in the Order


For repeat purchases, retain the agreed diameter, grade, acceptance criteria, and document requirements as the technical basis for the next order. Confirm revisions with us before production. For split deliveries, agree which records will accompany each shipment and how shipped quantities will be linked to their lots.


Include the following in the purchase specification:

  • Product: diameter, material grade, and quantity for each order line.

  • Identification: lot references and their agreed location on shipment or packaging documents.

  • Verification: required characteristics, methods, measurement or specimen conditions, sampling, and acceptance limits.

  • Documentation: reports required for each lot or shipment and when they must be submitted.

  • Review and release: requirements for holds, partial release, additional verification, and approved deviations.


If your receiving team uses a report template, send it with the inquiry. Identify mandatory fields and distinguish individual measurements from summaries. Where supplier qualification documents are also required, list them separately from the lot-specific results. Resolve reporting questions before production so the delivered records match the review your team must perform.


Agree on Batch Acceptance Before Production


Release a forged steel grinding ball batch once its identity is confirmed and its required results meet the order under the agreed methods. Keep missing evidence separate from confirmed nonconformities, and review certificates and process records only for the requirements they cover.


To review acceptance requirements for your next order, send us your purchasing specification, required diameters and grades, quantities, and receiving inspection template. Identify the test reports and qualification documents you need before shipment. Email ebiz@iraeta.com or submit your grinding ball inquiry.


Your privacy is important to us

We use cookies to personalize and enhance your browsing experience on our website.

By clicking "Accept all cookies", you agree to the use of cookies. You can read our Cookie Policy for more information.

Accept
Reject
伊莱特
伊莱特

Service hotline

400-9001-531

More Contacts
伊莱特
伊莱特